Please 'Boom' Responsibly As most of you have noticed, the noise ordinances have become much tougher lately. Most of this is due to idiots, yes IDIOTS, who drive through residential areas with their windows down while their system is playing at full power. To make things worse, the music they listen to has all sorts of foul language that's not suitable for small children, (who may be playing outside). There are even a few people, who are even beyond idiot status, that play their systems at full power through residential areas after 10:00 PM (when many people go to bed). I don't believe that this type of behavior is good for the industry. If the fines get too stiff, people will stop buying large systems. If this happens, more people will get out of car audio (who wants a mediocre system). People get interested in things because they're exciting. A deck and four 6.5" speakers are not going to interest many of the younger car audio enthusiasts. If car audio enthusiasts keep annoying more and more people, the fines will keep getting tougher. All of this will only reduce interest in the equipment that fuels the industry. If you want to listen to your system at full volume, get out on the highway where there's little chance of bothering anyone. When you get to a red light, turn it down. If the only thing attractive about you is your 'system', you have some work to do. Bottom line... Think about what you're doing. Think about other people. It's not the end of the world if you have to turn the volume down for a little while.


OHM'S law
There are 2 base formulae which will help you to understand the relationship between current , voltage , resistance and power . If you have any two of the parameters, you can calculate the other two parameters.

 

OHM'S LAW
BASE FORMULAS P=I*E E=I*R  
TO FIND VOLTAGE E=P/I E=I*R E=SQR(P*R)
TO FIND CURRENT I=P/E I=E/R I=SQR(P/R)
TO FIND POWER P=I*E P=E2/R P=I2*R
TO FIND RESISTANCE R=E2/P R=E/I R=P/I2
P = Power in Watts
E = Electromotive Force in Volts
I = Electrical Current in Amps
R = Electrical Resistance in Ohms
SQR = Square Root
Note:
I use 'E' to represent voltage most of the time but sometimes you'll see 'V' used for voltage. Don't let it confuse you.

Short Refresher Course

Change of Resistance: In the following diagram, you can see that the only difference between the diagrams on the left and the diagrams on the right is the resistance in each 'system'. The resistance in the faucet corresponds to the amount that the valve is open. In the wire, the resistance is the size of the opening* in the piece of wire. You can see that the voltage/pressure is the same for both the left and right examples. What you should note in this diagram is... All else being equal, if there is an increase in resistance, the current flow will be reduced. You can see that the current flow in the rightmost wire is half of the current flow in the leftmost wire. This is because the rightmost wire has half of the area for the electrons to pass through.

*Please note that the size of the 'opening' is is analogous to resistance. There is no physical restriction in a real piece of wire.

With the formula: I = E/R You can see that the current flow is inversely proportional to the resistance in the circuit.

More Resistance = Less Current

And for those who are more graphically inclined...

I = E/R


Change of Voltage: In the following diagram, you can see that the resistance in all of the systems is equal. This time we made a change in the voltage/pressure. You can see that the increased voltage causes an increase in current even though the resistance in both the left and right systems is equal.

With the formula: I = E/R You can see that the current flow is directly proportional to the voltage applied to the resistance.

More Voltage = More Current

I = E/R


Well, now that that's been explained to death, onto the math!


Mathematical Example:
In the following example, we know that we have 12 volts applied to a 10 ohm resistor. If you want to know how much power dissipation there is in the 10 ohm resistor, use the formula:
P = E2/R
P = 122/10
P = 144/10.
P = 14.4 watts
The power dissipation in the resistor is 14.4 watts.
 
If you wanted to know how much current was flowing through the resistor, you would use the formula:
 
I = E/R
I = 12/10
I = 1.2 amps
The current through the resistor is 1.2 amps.

If you want more examples, the resistor page has more fun than a barrel of monkeys.


If you want to try a few for yourself, the calculators below will allow you to check your math.

Find: Power dissipation and Current flow from Resistance and applied Voltage.

Data Input:
Resistor Value? = Ohms
Applied Voltage? = Volts
Data Output:
Power Dissipation = Watts
Current Flow = Amps

Find: Circuit Resistance from Current Flow and applied Voltage.

Data Input:
Applied Voltage? Volts
Current Flow? Amps
Data Output:
Resistor Value = Ohms

Find: Applied Voltage and Current Flow from Power Dissipation and Circuit Resistance.

Data Input:
Power Dissipation? = Watts
Resistor Value? = Ohms
Data Output:
Applied Voltage = Volts
Current Flow = Amps


Note:
In the following demo, you can adjust the voltage and the resistance of the circuit. Changing either one will change the current flow and power dissipation in the circuit. You should realize that an amplifier produces a voltage into a given load. The combination of the two will result in power dissipation (in the speaker's voice coil in the case of audio). Since an amplifier can produce a limited amount of voltage (limited by the internal power supply's design), the power output is limited when driving a given load (i.e. a 4 ohm load). To be able to produce more power, you can drive a lower impedance (resistance) load (within reason). This means that if you go from a 4 ohm load to a 2 ohm load, the power will double (assuming that the power supply is regulated). If we use the example of a 100 watt mono amplifier (100 watts into a 4 ohm load), we know it can produce no more than 20 volts across the speaker. If you set the voltage slider below to 20 volts, and the resistance slider to 4, you can see that the power is 100 watts. If you move the resistance slider to 2 ohms, you can see that the power is doubled (to 200 watts). Now, I know that I'm showing a battery as the voltage source (instead of an amplifier) but the concept is the same.

Click HERE to make it fill this window.


More Info:
Try the wire and resistor pages.

Historical Information

Georg Simon Ohm:
Georg Simon Ohm was a German physicist that lived from 1789 to 1854. He discovered the relationship between voltage, current and resistance in a conductor of a constant temperature (constant temperature is important because resistance changes with temperature and Ohm's law doesn't deal with the changing temperature/resistance). He found that, with a constant resistance, voltage and current were directly proportional (as we showed in a graph above). This relationship can be expressed as V=IR where V is the voltage applied to the resistance, I is the current flow through the resistance and R is the resistance in ohms.
James Watt:
James Watt was a Scottish inventor that lived from 1736 to 1819. The unit of measure for power, the watt, was named in his honor.
James Prescott Joule:
James Prescott Joule was an English physicist that lived from 1818 to 1889. He discovered the relationship between the power dissipated in a resistor and the current flow through the resistor. This relationship can be represented by the formula P=I²R where P is the power dissipation in watts, I is the current flow in amps R is the resistance in ohms. Ohm is generally given credit for the formulas which express the relationship between Power, Current, Resistance and Voltage but the credit probably should go to Joule.
The 'Joule' as a unit of measure:
A 'Joule' represents the amount of energy used when 1 watt is dissipated for 1 second (or 1 watt-second).

You should remember:
1.If you have any 2 of the 4 electrical properties, you can find the other properties through Ohm's law.


backward If you find a problem with this page or feel that some part of it needs clarification, E-mail me.

This is a link to this site's home page.

forward